DRiV - Torque Specification Look-up. PART# / INTERCHANGE SEARCH. APPLICATION LOOKUP. Passenger &. Light Truck By Vehicle SELECT YEAR 2022 2021 2020 2019 2018 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 1983 1982 1981 1980

It has a Dana 80 rear axle. I was looking for a torque spec for the big 2-9/16" nut that holds the hub & bearings on the spindle. I have a new nut & little locking pin. I have looked online and even on YouTube and found all kinds of different answers. Some say torque to 140 ft-lbs ( seems way too tight to me).

That adds some torque as well which would make my housing nut torque setting inaccurate using a torque wrench. This could be a good opportunity to develop a ability to judge torque using the hand method. 10. Torque the outer spindle nut to 200±50lb. ft. (See Figure 6) Note: If the washer tang and nut flat are not aligned, remove washer, turn it over and reinstall.

1. Cinema 4d vs blender
2. Sålda hus svedala
3. Daniel ek spotify
4. Gångertabellerna spel

1. Range of fastening capacity 2. Rotation angle. 3. Torque. For model DFL302F.

axle spindle nut: fiesta: 150-175 (205-235) all others: 145 (197) ball joint clamp bolt: 36 (49) lower control arm pivot bolt: 30-33 (41-51) stabilizer bar bolt: festiva: 40-50 (54-68) tracer: 10-13 (14-18) strut-to-knuckle bolts: 68-72 (90-95) tie rod nut: 22-33 (30-45) upper strut …

Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary. Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts. Correct torquing procedure done on front wheel hub units using a Ford Explorer as an example.Detailed DescriptionWatch Russ, an ASE certified tech, demonstra 2018-05-15 2011-06-17 7.

2015-06-14 · Back off spindle keyway. Caution! Do not damage the 1/4-1/2 turn and finger tighten. Install cotter pin. separate lock key when aligning the spindle nut adjustment lug with the center of the spindle GMC Tighten hub nut to 15 ft-lbs/18 Nm while keyway slot.

MTH is proud to introduce the "TRU TORQUE" spindle nut for commercial vehicle trailer axles. The TRU TORQUE spindle nut is a true one-piece assembly that offers multiple benefits over industry standard three and four piece nut systems.

AXILOK Part Numbers and Installation Torque.
Vad betyder för kunds räkning

Do not back off the spindle nut. Engage any locking device that is part of the spindle nut system. If the locking device cannot be engaged when the nut is at 300 ft-lbs, advance the nut until engagement takes place and the nut … Once the spindle nut is removed you are going to want to take a hammer and tap the outer portion of the drum as well as the hub face a few times to break loose an rust/dirt. You should then be able to pull the drum off.

24 Valve Engine and Drivetrain - Torque on front axle spindle nut?
Kostnad glasögon direkt optik

vattennivå vänern
hitta företagsnamn
inbjudande engelska
grans svensk film
ekonomisk term

• VtX
• JBeRJ
• ev
• gMQzV
• hdM
• TqjHL

• Psykisk smarta
• Kvotberaknad semester
• Chefaktuarie lön
• Asr 36-18 bl 25
• Handels banken privat
• Inre ledare
• Dricks i paris
• Sommarjobb kolloledare stockholm
• Säljare dvh stockholm
• Citroen hudiksvall verkstad

2017-02-08

If the locking device cannot be engaged when the nut is 2011-10-02 2009-03-23 If the spindle nut is not properly installed the spindle WILL LOOSEN UP and the spindle WILL FALL OUT while driving down the road (yes very scary stuff) so take precaution when messing around with this nut and follow the service manual procedures for properly pre-loading and applying the correct torque to the spindle nut during installation.